精品精品-精品精品国-精品精品国产-精品精品国产高-精品精品国产高清-精品精品国产国产-精品精品国产精品等-精品精品国产理论

現有10個搶答器，最先按按鈕的搶答器前燈亮。而且要知道10個搶答器的搶答先后順序。這程序怎么寫？？？？？

看看利用互鎖能否實現

互鎖是能解決只一燈亮問題，但第2按下的，第3的，第4，5.。。。。搶答先后順序還是沒法。。

用腳本語言可以實現，遵守先進先出原則就可以

(* 呼叫編號暫存******************************************************************************)
hj[0]:=a11_hj; hj[1]:=a12_hj; hj[2]:=a13_hj; hj[3]:=a14_hj; hj[4]:=a15_hj;  hj[5]:=a16_hj;
hj[6]:=b11_hj; hj[7]:=b12_hj; hj[8]:=b13_hj; hj[9]:=b14_hj; hj[10]:=b15_hj; hj[11]:=b16_hj;
(*送料滿斗后，清料標志     ******************************************************************)
qingliao[0]:=a11_qingliao_finished;qingliao[1]:=a12_qingliao_finished;qingliao[2]:=a13_qingliao_finished;
qingliao[3]:=a14_qingliao_finished;qingliao[4]:=a15_qingliao_finished;qingliao[5]:=a16_qingliao_finished;
qingliao[6]:=b11_qingliao_finished;qingliao[7]:=b12_qingliao_finished;qingliao[8]:=b13_qingliao_finished;
qingliao[9]:=b14_qingliao_finished;qingliao[10]:=b15_qingliao_finished;qingliao[11]:=b16_qingliao_finished;
qingliao[12]:=c11_qingliao_finished;qingliao[13]:=c12_qingliao_finished;qingliao[14]:=c13_qingliao_finished;
qingliao[15]:=c14_qingliao_finished;qingliao[16]:=c15_qingliao_finished;qingliao[17]:=a16_qingliao_finished;
(*移位處理***********************************************************************************)
(*addr[0]存儲的是最先響應的料斗編號**********************************************************)
for k:=0 to 18 by 1 do
    if addr[k]=0 and addr[k+1]<>0 then
        addr[k]:=addr[k+1];
        addr[k+1]:=0;
    end_if;
end_for;
(********************************************************************************************)
(*先呼叫，先響應。12個呼叫存儲滿后，禁止再儲存呼叫號碼。*************************************)
for i:=0 to 18 by 1 do
    if j=0 then
        if hj=true then
            if addr[0]=0 then
                addr[0]:=i+1;
                j:=1;
            elsif addr[1]=0 then
                addr[1]:=i+1;
                j:=1;
            elsif addr[2]=0 then
                addr[2]:=i+1;
                j:=1;
            elsif addr[3]=0 then
                addr[3]:=i+1;
                j:=1;
            elsif addr[4]=0 then
                addr[4]:=i+1;
                j:=1;
            elsif addr[5]=0 then
                addr[5]:=i+1;
                j:=1;
            elsif addr[6]=0 then
                addr[6]:=i+1;
                j:=1;
            elsif addr[7]=0 then
                addr[7]:=i+1;
                j:=1;
            elsif addr[8]=0 then
                addr[8]:=i+1;
                j:=1;
            elsif addr[9]=0 then
                addr[9]:=i+1;
                j:=1;
            elsif addr[10]=0 then
                addr[10]:=i+1;
                j:=1;
            elsif addr[11]=0 then
                addr[11]:=i+1;
                j:=1;
            elsif addr[12]=0 then
                addr[12]:=i+1;
                j:=1;
            elsif addr[13]=0 then
                addr[13]:=i+1;
                j:=1;
            elsif addr[14]=0 then
                addr[14]:=i+1;
                j:=1;
            elsif addr[15]=0 then
                addr[15]:=i+1;
                j:=1;
            elsif addr[16]=0 then
                addr[16]:=i+1;
                j:=1;
            elsif addr[17]=0 then
                addr[17]:=i+1;
                j:=1;
            end_if;
        end_if;
    end_if;
    (*呼叫的清除************************************************************************************)
    (*外部呼叫結束：即外部下位電眼處已經有粉料，同時延時時間到達************************************)
        if not hj and qingliao=true then
            if addr[0]=i+1 then
                addr[0]:=0;
                j:=0;
            elsif addr[1]=i+1 then
                addr[1]:=0;
                j:=0;
            elsif addr[2]=i+1 then
                addr[2]:=0;
                j:=0;
            elsif addr[3]=i+1 then
                addr[3]:=0;
                j:=0;
            elsif addr[4]=i+1 then
                addr[4]:=0;
                j:=0;
            elsif addr[5]=i+1 then
                addr[5]:=0;
                j:=0;
            elsif addr[6]=i+1 then
                addr[6]:=0;
                j:=0;
            elsif addr[7]=i+1 then
                addr[7]:=0;
                j:=0;
            elsif addr[8]=i+1 then
                addr[8]:=0;
                j:=0;
            elsif addr[9]=i+1 then
                addr[9]:=0;
                j:=0;
            elsif addr[10]=i+1 then
                addr[10]:=0;
                j:=0;
            elsif addr[11]=i+1 then
                addr[11]:=0;
                j:=0;
            end_if;
        end_if;
end_for;
(*呼叫的影應****************************************************************************************)
case addr[0] of
    1:   a11_yd:=true;  
    2:   a12_yd:=true;
    3:   a13_yd:=true;    
    4:   a14_yd:=true;
    5:   a15_yd:=true;  
    6:   a16_yd:=true;  
    7:   b11_yd:=true;
    8:   b12_yd:=true;
    9:   b13_yd:=true;
   10:   b14_yd:=true;
   11:   b15_yd:=true;
   12:   b16_yd:=true;
   13:   c11_yd:=true;
   14:   c12_yd:=true;
   15:   c13_yd:=true;
   16:   c14_yd:=true;
   17:   c15_yd:=true;
   18:   c16_yd:=true;
    else
         a11_yd:=false; a12_yd:=false; a13_yd:=false; a14_yd:=false; a15_yd:=false; a16_yd:=false;
         b11_yd:=false; b12_yd:=false; b13_yd:=false; b14_yd:=false; b15_yd:=false; b16_yd:=false;
         c11_yd:=false; c12_yd:=false; c13_yd:=false; c14_yd:=false; c15_yd:=false; c16_yd:=false;end_case;
addrr0:=addr[0];

謝謝3樓，腳本語言不太懂，能否用梯形圖等等。

用梯形圖即可

可是試試用位置偏移的方式來存儲數據